Changing a furnace filter is a 5-minute job that needs no tools. The swap itself is easy. What trips people up is the stuff around it: buying the wrong size, sliding the new filter in backwards, or picking a filter so dense the furnace has to strain to pull air through it. This guide walks through the swap step by step, then covers all three of those problems so you only have to do it once.
Quick answer: Turn the system off at the thermostat. Find the filter slot and photograph the old filter’s size and arrow. Slide it out, vacuum the slot, and slide the new filter in with the arrow pointing toward the furnace blower. Close the panel, turn the system back on, and write the date on the new filter’s frame.
Quick Picks
- Best value everyday filter (MERV 8): Simply MERV 8, 6-Pack
- Best for pets and allergies in a 1-inch slot (MERV 11): Filtrete MPR 1000, 2-Pack
- Best 4-inch media filter (MERV 13): AprilAire 213
Comparison Table
Prices and ratings are from Amazon on 2026-11-18 and change often. Prices shown are for the sizes listed; switch the size on the Amazon page to match your furnace.
| Product | MERV | Size shown | Pack | Price | Rating |
|---|---|---|---|---|---|
| Simply MERV 8 | 8 | 16x25x1 | 6 | $29.96 | 4.7 (55,549) |
| Filtrete MPR 1000 | 11 | 16x25x1 | 2 | $22.99 | 4.8 (59,177) |
| AprilAire 213 | 13 | 20x25x4 | 1 | $64.99 | 4.8 (23,691) |
What You Need
- A new filter in the right size (more on sizing below)
- A flashlight. Furnace closets and basements are dark, and the size print on the frame is small. Our rechargeable flashlight picks cover a few good options.
- A vacuum with a brush attachment
- A marker
Most setups need no tools. A few return grilles use a screw or two to hold the cover, so keep a screwdriver nearby just in case.
Where Is Your Furnace Filter?
The filter always sits on the return side, between the rooms and the blower. In most homes, it’s in one of three places.
Inside the blower compartment
Open the lower panel on the furnace. The filter may slide into a rack right in front of or beside the blower. These furnaces have a safety switch that cuts power when the panel is off.
In a slot between the return duct and the furnace
This is the most common setup. Look for a thin cover or slot where the large return duct meets the side or bottom of the furnace. Pull the cover off and the filter slides out.
Behind a return air grille
Some homes put the filter in a large grille on a wall or ceiling, often in a hallway. Flip the latches, swing the grille open, and the filter sits right behind it.
Some homes have a filter at the grille and another at the furnace. Unless your system was designed for both, you only need one. Two filters in a row restrict airflow more than either one alone.

How to Change a Furnace Filter: Step by Step
- Turn the system off. Set the thermostat to Off. If the filter is inside the furnace cabinet, also flip the service switch on or near the furnace. This keeps the blower from pulling dust in while the slot is open.
- Open the slot, panel or grille. Pull the filter cover off, remove the lower panel, or open the return grille.
- Photograph the old filter. Before you pull it out, take a phone photo of the frame. You want the size printed on the edge and the direction of the airflow arrow.
- Slide the old filter out slowly. Keep it level so the dust stays on it. Drop it straight into a trash bag.
- Vacuum the slot. Run the brush attachment around the slot and the edges of the grille. A shop vacuum handles this well if your house vacuum doesn’t reach.
- Slide the new filter in, arrow toward the blower. Push it all the way in. It should sit flat, with no gaps around the edges and no bent frame.
- Close up and restart. Put the cover or panel back, make sure any panel switch is pressed in, and turn the system back on. Write today’s date on the edge of the new filter.
Which Way Does a Furnace Filter Go?
The arrow on the frame follows the air. Air travels from your rooms, into the return duct, through the filter and into the blower. So the arrow always points toward the blower and away from the room.
The rule never changes, but where the arrow ends up pointing does, depending on how your furnace is set up.
| Setup | Where you’ll usually find it | Arrow points |
|---|---|---|
| Upflow furnace | Basement or utility room; filter at the bottom | Up, toward the blower |
| Downflow furnace | Upper floor, closet or attic; filter at the top | Down, toward the blower |
| Horizontal furnace | Attic, crawl space or garage | Sideways, toward the blower end |
| Wall return grille | Hallway or living area | Into the wall, away from the room |
| Ceiling return grille | Hallway ceiling | Up, into the ductwork |
Filterbuy states the same rule, noting it holds for upflow, downflow and horizontal furnaces and for wall, floor and ceiling returns, and points to the U.S. Department of Energy’s Building America Solution Center for the same guidance (Filterbuy, retrieved 2026-11-18). Some downflow furnaces use a V-shaped rack that holds two filters. Both arrows still point down toward the blower.
No arrow on the filter?
Some filters have wire mesh or a stiffer backing on one side. That side faces the blower. Once you’ve worked out the direction, draw a big arrow on the furnace cabinet with a marker. Next time, you just match it.
How to Find the Right Filter Size
The size is printed on the edge of the old filter as length x width x depth, like 16x25x1. That’s the number you shop by.
Here’s the part that confuses people: the printed size is a rounded label, called the nominal size. The filter itself is a little smaller so it slides in easily. A filter sold as 16x25x1 actually measures about 15.5 x 24.5 x 0.75 inches (Filterbuy, retrieved 2026-11-18). So if you measure your old filter and get 15.5 x 24.5, don’t go hunting for an odd size. Buy the 16x25x1.
No label on the old filter? Measure the slot itself, including its depth, and round each number up to the nearest inch.
Why fit matters: A filter that’s too small leaves a gap, and air takes the easy path around the edges, carrying dust straight into the blower. One that’s too big gets bent to fit, which opens gaps of its own.
What MERV Rating Should You Buy?
MERV stands for Minimum Efficiency Reporting Value. The higher the number, the smaller the particles the filter catches. Higher numbers also mean denser filter material, which makes the blower work harder to pull air through.
Shopping gets confusing because two big brands use their own scales. Filtrete (3M) uses MPR, and Home Depot uses FPR. They line up roughly like this:
| MERV | Filtrete MPR | Home Depot FPR | Good for |
|---|---|---|---|
| 8 | 600 | 5 | Everyday dust, lint and pollen |
| 11 | 1000-1200 | 7 | Pets and allergies |
| 13 | 1500-1900 | 10 | Allergies, smoke, fine particles |
These are approximate translations (Remember the Filter, retrieved 2026-11-18). When you compare across brands, go by MERV, since it’s the industry-wide scale.
Can your furnace handle MERV 13?
The EPA’s advice is to choose a filter rated at least MERV 13, or as high as your system will accommodate (EPA Guide to Air Cleaners in the Home, retrieved 2026-11-18). The catch is that last part. Here’s how to tell:
- 4-inch media cabinet: built for high-MERV filters. MERV 13 is usually fine.
- 1-inch slot: MERV 8 to 11 is the safe range. You can try MERV 13, but watch for whistling at the grille, weaker airflow at the vents, or the furnace running noticeably longer. If you notice any of those, step back down.
- Not sure: check the furnace manual, or ask your HVAC tech at the next service visit.
The Minnesota Center for Energy and Environment goes further: if you want a filter above MERV 8, it suggests using a 4-inch filter rather than a 1-inch one (MNCEE, retrieved 2026-11-18).
How Often Should You Change a Furnace Filter?
ENERGY STAR’s rule is simple: check the filter every month, especially in winter and summer. If it looks dirty after a month, change it. At a minimum, change it every 3 months (ENERGY STAR, retrieved 2026-11-18).
Thickness changes the schedule. These are Bryant’s guidelines (Bryant, retrieved 2026-11-18):
| Filter type | Replace every |
|---|---|
| 1-inch fiberglass | 30 days |
| 1-inch pleated | 60-90 days |
| 4-inch media | 6-12 months |
Change sooner if you have pets, someone in the house has allergies, you’ve been sanding or remodeling, or the furnace is running hard through a cold snap.
The quick monthly check: pull the filter and hold it up to a light. If you can barely see light through it, swap it, whatever the calendar says.
Best Furnace Filters on Amazon
One pick for each MERV level in the table above. The prices are for the sizes shown. All three come in other sizes, so pick yours on the Amazon page.
1. Simply MERV 8 – Best Value Everyday Filter
This is the safe default for any furnace. The 16x25x1 6-pack was $29.96 on 2026-11-18, down from a $40.97 list price, which works out to about $5 a filter. It rates 4.7 stars across 55,549 ratings.
The listing does something we like: it prints the actual size right in the title. For the 16x25x1, that’s 15.75 x 24.75 x 0.75 inches, which matches the nominal vs actual rule above. The filters are pleated, rated for up to 3 months, and made in the USA per the listing.
Key specs: MERV 8; pleated; up to 3 months; actual size listed (per listing).
Pros: Low cost per filter; huge rating count; MERV 8 is easy on any blower.
Cons: MERV 8 catches dust and pollen, not fine particles or smoke. A 6-pack locks you into one size for a year or more.
Not the right fit if: you have pets or someone in the house has allergies. Look at the Filtrete MERV 11 next.
2. Filtrete MPR 1000 (MERV 11) – Best for Pets and Allergies in a 1-Inch Slot
This is the most-reviewed filter in our search. The 16x25x1 2-pack was $22.99 on 2026-11-18, or about $11.50 a filter. It rates 4.8 stars across 59,177 ratings.
Filtrete labels it MPR 1000, and the listing also gives MERV 11. That’s the step up most 1-inch systems can handle without airflow problems. The listing describes it as a 3-month pleated filter and says it’s certified asthma and allergy friendly.
Key specs: MERV 11 / MPR 1000; pleated; 3-month rating (per listing).
Pros: Catches more pet dander and fine dust than MERV 8; very large rating count; a sensible upgrade for a standard 1-inch slot.
Cons: Costs about twice as much per filter as the Simply. Filtrete puts the MPR number front and center, so you have to translate it to compare with other brands.
Not the right fit if: you want MERV 13 in a 1-inch slot. Filtrete makes an MPR 1900 (MERV 13) version (4.8 stars, 17,553 ratings), but watch your airflow after switching.
3. AprilAire 213 (MERV 13) – Best 4-Inch Media Filter
If your furnace has an AprilAire whole-house air cleaner cabinet, this is its MERV 13 filter. One 20x25x4 filter was $64.99 on 2026-11-18. It rates 4.8 stars across 23,691 ratings. A 2-pack was $125.98.
A 4-inch media filter is where MERV 13 makes the most sense. The deep pleats give the air far more surface to pass through, so you get fine filtration without choking the blower, and you change it every 6 to 12 months instead of every 2 to 3. Per the listing, it fits AprilAire whole-house purifier models 1210, 1620, 2210, 2216, 3210 and 4200, plus some 2120 and 2200 units.
Key specs: MERV 13; 20x25x4 media filter; fits listed AprilAire cabinet models (per listing).
Pros: MERV 13 filtration that’s easier on the blower than a 1-inch MERV 13; far fewer changes per year.
Cons: Fits AprilAire cabinets only. It is not a drop-in for any slot labeled 20x25x4. It’s also the most expensive filter here, though spread over 6-12 months the yearly cost is closer than it looks.
Not the right fit if: you have a standard 1-inch slot, or a 4-inch cabinet from another brand. Match the model number on your cabinet first.
Troubleshooting After a Filter Change
- Furnace won’t start: if you took the lower panel off, the door safety switch may not be pressed in. Reseat the panel firmly. Also check that the service switch and the thermostat are back on.
- Whistling at the grille or furnace: the filter may be too dense for the system, or there’s a gap the air is squeezing through. Check the fit first, then try a lower MERV.
- Weak airflow at the vents: same causes. A filter that went in backwards can also do it.
- Filter bowing or getting sucked in: the filter is too small for the slot, or it’s a cheap flat filter collapsing under the pull. Use the right size and a pleated filter with a stiff frame.
- Cold air from the vents: usually not the filter. Check the thermostat is set to Heat and not just Fan. If it continues, call a technician.
Mistakes to Avoid
- Buying by your tape measure: shop by the nominal size printed on the frame.
- Arrow facing the room: it always points toward the blower.
- Stacking two filters: it doubles the restriction without much benefit.
- Running with no filter: dust goes straight onto the blower and coil.
- Washing a disposable filter: unless the filter says it’s washable, it isn’t.
- Forgetting the date: write it on the frame every time.
While you’re in the utility room, it’s a good moment to check your smoke and CO alarms too. Here’s how long smoke detectors last and how to read the date on yours.
FAQ
Is the furnace filter the same as the AC filter?
In most homes, yes. Central heating and air conditioning share one blower, so one filter serves both.
Do I have to turn off the furnace to change the filter?
Yes. Set the thermostat to Off so the blower doesn’t pull dust into the system while the slot is open. If the filter is inside the cabinet, turn off the service switch too.
Can I run my furnace without a filter for a day?
Try not to. Without a filter, dust lands on the blower and the coil, which are harder to clean than a filter is to replace. If you’re caught without one, keep the system off until you can buy one, or run it for as short a time as possible.
Can I clean and reuse a disposable furnace filter?
No. Vacuuming a disposable filter removes surface dust but leaves the fine particles buried in the material. Only filters labeled washable or reusable should be cleaned.
Is MERV 13 too high for my furnace?
It depends on the slot. A 4-inch media cabinet usually handles MERV 13 well. In a 1-inch slot, it can restrict airflow on some systems. Try it and watch for whistling, weak vents or longer run times.
What happens if I put the filter in backwards?
The filter won’t catch dust as well, and some filters can deform over time. Turn it around at the next check.
Why is my furnace blowing cold air after changing the filter?
Most often, a panel isn’t seated properly, or the thermostat was left on Fan. Reseat the panel, set the thermostat to Heat, and give it a few minutes. If it still blows cold, call a technician.
How much does a furnace filter cost?
At the time of writing, a basic 1-inch MERV 8 pleated filter runs about $5 each in a multi-pack, a MERV 11 about $11, and a 4-inch MERV 13 media filter $60 or more. Thicker filters cost more each but last much longer.
Bottom Line
Find your slot, read the size on the frame, and point the arrow at the blower. Then pick the filter by slot and household:
- Standard 1-inch slot, no pets or allergies: Simply MERV 8.
- 1-inch slot with pets or allergies: Filtrete MPR 1000 (MERV 11).
- AprilAire 4-inch cabinet: AprilAire 213 (MERV 13).
Check it every month, change it at least every 3 months, and write the date on the frame.











